Honda Accord Caliper Bracket Bolt Torque Specifications

The recommended torque for Honda Accord calliper bracket bolts is typically around 80 ft-lbs (108 Nm). However, always confirm the exact spec in your vehicle’s manual, as it can vary.

As a mechanic with years of experience, I’m often asked about the proper procedures for torquing Honda Accord caliper bracket bolts. In this comprehensive DIY guide based on my expertise, I’ll walk through everything you need to know, from understanding torque specs to step-by-step torquing instructions. 🧰

Table of Contents

Why Proper Torque Matters for Caliper Bracket Bolts

The caliper bracket bolts secure the brake caliper bracket to the wheel hub. If these bolts loosen over time or aren’t installed to the proper torque specifications, it can lead to:

❌ Uneven brake pad wear

❌ Excessive vibration and noise when braking

❌ Reduced braking power and even brake failure

That’s why the Honda Accord Caliper Bracket Bolt Torque is so important – it ensures this crucial braking component functions safely and efficiently. 🚘

Honda Accord Caliper Bracket Bolt Torque Specs

The torque specification for Honda Accord caliper bracket bolts is typically around 80 ft-lbs (108 Nm).

However, you should always confirm the exact torque setting in your vehicle’s factory service manual, as it can vary slightly between models and years.

For example:

2013 Honda Accord: 80 ft lbs
2017 Honda Accord: 79 ft lbs
2022 Honda Accord: 82 ft lbs

Small differences like these when torquing bolts on modern vehicles can have a noticeable impact. So, double-checking your manual is crucial.

Necessary Tools To Torque the Bolts

Torquing caliper bracket bolts requires having the right tools for the job. Here’s what you’ll need:

Torque Wrench

A high-quality 3/8” drive torque wrench capable of reaching the needed 80 ft-lb torque specification accurately. Quality brands like Snap-On, Craftsman, and GearWrench are good options.

The wrench should have an accuracy rating of ±4% or better from 20%-100% of its torque range.

Socket Set

A socket set with metric sockets fitting the caliper bracket bolt sizes on your Accord. Common sizes are 14mm, 15mm, and 17mm, but confirm yours.

Breaker Bar

Helpful for initially loosening the caliper bracket bolts before torquing. Allows added leverage.

Safety Gear

Gloves, eye protection, jack stands, and chock blocks for safety.

Step-By-Step Torquing Instructions

Now that you understand the Honda Accord caliper bracket bolt torque specs and have the right gear let’s walk through the full process:

Loosen Bolts

Break loose the old bolts with a breaker bar and socket. Don’t fully remove it yet.

🔧

Support Vehicle

Lift the vehicle safely using a floor jack and secure on jack stands. Chock rear wheels.

🚗

Clean Components

Use a wire brush and brake cleaner to remove corrosion and debris from bolts, brackets, and hubs🧽.

Apply Thread Locker

Put a small dab of medium-strength thread locker on bolt threads to prevent loosening.💧

Hand Thread Bolts

Thread caliper bracket bolts into the hub by hand until snug. Ensure proper alignment.👌

Torque Bolts

Use calibrated torque wrench and socket to precisely torque bolts to factory spec. Tighten in a crisscross pattern.🔧

Safety Check

Double-check torque on all bolts and proper caliper bracket alignment before driving🏁.

Following these best practices when torquing the Honda Accord caliper bracket bolts will maintain the critical alignment and security of your brake system for safe operation. Let me know if you have any other questions!

What Is the Torque on Caliper Bolt Brackets?

The torque specification for caliper bolt brackets can vary depending on the make and model of the vehicle, but a common torque value for caliper bracket bolts is around 80 ft-lbs (108 N·m). It’s essential to refer to your vehicle’s specific service manual or consult a qualified mechanic for the exact torque requirements, as they can differ from one car to another.

What Is the Torque on a 17mm Brake Caliper Bolt?

The torque specification for a 17mm brake caliper bolt also depends on the vehicle’s make and model. However, a typical torque value for a 17mm caliper bolt falls in the range of 25 to 35 ft-lbs (34 to 47 N·m). To ensure safety and proper brake performance, always follow the manufacturer’s recommendations found in the service manual for your specific vehicle.

What Is the Torque on the Lug Nuts on a 2013 Honda Accord?

The recommended torque for the lug nuts on a 2013 Honda Accord is 108 N·m (11.0 kgf·m, 80 lbf·ft). It’s crucial to adhere to this specification to prevent over-tightening or under-tightening the lug nuts, which can affect wheel stability and brake performance.

What Are Brake Caliper Brackets?

Brake caliper brackets are essential components of a vehicle’s braking system. They secure the brake caliper in place and play a crucial role in holding the brake pads and rotor in alignment. Over time, caliper brackets can wear out due to exposure to heat, moisture, and road debris.

When this happens, it’s essential to replace or refurbish them to maintain the effectiveness of your braking system and ensure safe operation. Caliper brackets are a vital part of the overall brake assembly, and their proper functioning is essential for efficient and safe braking.

Frequently Asked Questions

What Torque Is Recommended For The 2011 Honda Accord Rear Caliper Bracket Bolts?

The factory service manual specifies 80 ft-lbs (108 Nm) for torquing 2011 Honda Accord rear caliper bracket bolts. Always verify the specs for your particular model year’s bolts.

What Size Socket Do I Need To Torque The 2005 Honda Accord Front Caliper Bracket Bolts?

You’ll need a 14mm socket for torquing the front caliper bracket bolts on a 2005 Honda Accord. Having a matching 3/8-inch drive torque wrench is also essential.

How Often Should I Check The Honda Accord Caliper Bracket Bolt Torque?

It’s smart to inspect the Honda Accord caliper bracket bolt torque around every 3,000 miles or whenever swapping brake pads. Losing even 15% torque on these critical fasteners can allow components to shift and wear prematurely over time.

Is It Okay To Use An Impact Wrench To Install Honda Accord Caliper Bracket Bolts?

No, the use of an impact wrench is unsafe. Only a calibrated torque wrench provides the necessary precision and control when tightening caliper bracket bolts to factory torque values. Impacts can easily overstress or break bolts.

Conclusion

Properly torqueing the Honda Accord caliper bracket bolts is an essential step in maintaining your vehicle’s braking system. By understanding the torque specifications, using the right tools, and following the correct procedures, you can ensure that your brakes perform optimally and safely. Always consult your vehicle’s manual for specific torque specs and tightening sequences, and verify the applied torque to prevent damage or premature wear.

Also Read:

Ammar Masoud

I have had a long and fulfilling career in the automotive industry, primarily with Honda and Acura. With 15 years of experience as a Honda service technician, I became highly skilled in repair and maintenance, gaining a deep understanding of these vehicles. After many years in the automotive field, I decided to embark on a second career in industrial manufacturing. It was a significant change, but I found that the skills I had honed in the automotive industry were incredibly valuable in my new role. In my current position in industrial manufacturing, the demand for quality workmanship and meticulous attention to detail is paramount. Fortunately, these are traits that I have cultivated throughout my years in the automotive industry. I take pride in applying these skills to meet the high standards expected in the manufacturing sector.